PDA

צפייה בגרסה מלאה : HobbyKing Pitts EPP review



sharonx
17-10-2010, 00:27:44
Hello.

This is a review of HobbyKing Pitts EPP (http://www.hobbycity.com/hobbycity/store/uh_power_Search.asp).

Pitts EPP is an electric aerobatic biplane, made of EPP foam which is very resilient to crashes and almost unbreakable, thus very good for beginners.

Packaging :
As always - HK does a very good job packing their models. All parts were covered with bubble-wrap and taped to the box so they won't move or break.
A you can see - nothing was damaged or broken.

http://www.efly.co.il/forums/attachment.php?attachmentid=33314&stc=1&d=1287273643

Whats in the box ?
- EPP wings,fuse and tail
- 2212 1400KV 50g brushless motor + GWS 8040 prop
- Linkage hardware
- Black Fiberglass reinforcement rods
- Landing gear + wheel pants
- Instruction manual

http://www.efly.co.il/forums/attachment.php?attachmentid=33316&stc=1&d=1287273643

What you will need to complete the model :
- 1000-1300 3S Lipo
- 3pcs of 9g servo
- 20A ESC
- 4CH RX and TX
- Building materials : CA glue, CA accelerator, Ruler, hobby-knife

The Building :
The instructions in the manual were very clear. Each step is followed by an explanation and a color photo. There are 60 steps. The building took 5 hours.
Any beginner can build this model with such detailed instructions.

So let's begin:

Step 1 - Fuselage reinforcement rod
By using a ruler, some tape and hobby-knife I install the rod into the EPP. Glued it using CA.
http://www.efly.co.il/forums/attachment.php?attachmentid=33317&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33318&stc=1&d=1287273643

Step 2 - Firewall asembly
Make sure you put it together straigt
http://www.efly.co.il/forums/attachment.php?attachmentid=33320&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33321&stc=1&d=1287273643

Step 3 - Tail servo's installation
http://www.efly.co.il/forums/attachment.php?attachmentid=33322&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33323&stc=1&d=1287273643

Step 4 - Canopy asembly
You will need to cut holes for the servo arms
http://www.efly.co.il/forums/attachment.php?attachmentid=33338&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33339&stc=1&d=1287273643

Step 5 - Tail asembly
http://www.efly.co.il/forums/attachment.php?attachmentid=33324&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33326&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33327&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33328&stc=1&d=1287273643

Step 6 - Wings assembly
One fiberglass rod is enough because we will ad balsa supports later.
http://www.efly.co.il/forums/attachment.php?attachmentid=33330&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33340&stc=1&d=1287273643

Step 7 - Glueing the airlions servo arm extension
I added string for better bonding.
http://www.efly.co.il/forums/attachment.php?attachmentid=33331&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33301&stc=1&d=1287273643

http://www.efly.co.il/forums/attachment.php?attachmentid=33332&stc=1&d=1287273643

Step 8 - Wings X reinforcement
You need to reinforce the wings using X shape from fiberglass rods, one X in each side. This stiffens the wings very much.
http://www.efly.co.il/forums/attachment.php?attachmentid=33336&stc=1&d=1287273643

Step 9 - Tail skid
http://www.efly.co.il/forums/attachment.php?attachmentid=33341&stc=1&d=1287273643


Test Flight :
This motor has a lot of power. It hovers just over 1/2 throttle, and has a very good vertical power at full throttle. Takeoff from the hand is easy. Takoff and landing on the the runway is very fun - you can takeoff after 5 meters or let it ride and slowly pull up so you get a nice scaly takeoff.
Taxi is very easy thanks to the surprisingly efficient rudder.

The rudder, althogh looks very small for a 3D plane, does an excellent job in the air. The Alirons don't have enough throw so I will need to add a carbon stripe so all the ailerons will move and not just the part that is close to the horn. Also I consider changing to a 14g 2.5KG servo. The 9g 1.6KG servo I used can't move the 4 ailerons to their desired end-point.
I coun't attempt much 3D flight because of this, and after I fix this I will post a 3D flight video.

Just flying the model was great fun, very stable and easy to fly, thus suitable for begginers and medium-level flyers.

Landing this model on the runway is so much fun - take a look at the second half of the video.

http://www.efly.co.il/forums/attachment.php?attachmentid=33342&stc=1&d=1287273643



http://www.youtube.com/watch?v=dtf-Mg2uDqE


In Conclusion :
This is a very good model both for begginers and for experienced pilots who want a fun 3D park flyer. Building is easy and fast, the price of the model is low and its flying characteristics are very good.
Just need to fix the airlions problem and it will probably be a great 3D plane :).

אייל שפירא
17-10-2010, 09:01:03
BEAUTIFULLY DONE!!!

guyst
17-10-2010, 10:04:31
יפה מאוד! עכשיו הלחצת אותי לסיים את שלי מהר....:eek:

aofer
17-10-2010, 10:27:09
מגניב!!! תתחדש.

Death_Keeper
17-10-2010, 18:47:15
אחלה סקירה! ננסה לשפר את המאזנות, ואז יהיה מעניין יותר :)

MDreamer
17-10-2010, 21:24:41
שרוניקס! סקירה מעולה. מישהו כתב ב RCG שכדאי לפריד את המאזנות.. אולי זאת הבעיה.
אנחנו שמחים שמצאת זמן בשביל הסקירה תודה! ותהנה מהצעצוע החדש שלך:)
צוות eFly

sharonx
17-10-2010, 23:17:45
תודה רבה דרימר ושאר החברים.
נהנתי לבנות את הטיסן, פעם ראשונה שאני בונה דו-כנפי וזה שונה במקצת מכנף בודדת.

אני אנסה את הפטנט של המאזנות. חשבתי בהתחלה להוסיף סטריפ קרבון לאורך במאזנת אבל לא בטוח כמה זה יעזור וגם יוסיף משקל.

sharonx
17-10-2010, 23:18:23
שרוניקס! סקירה מעולה. מישהו כתב ב RCG שכדאי לפריד את המאזנות.. אולי זאת הבעיה.
אנחנו סמים שמצאת זמן בשביל הסקירה תודה! ותהנה מהצעצוע החדש שלך:)
צוות eFly

אולי כדאי שתפסיק קצת עם הסמים ? :D:D:D

s.mario
18-10-2010, 07:59:06
יופי של בניה וסקירה שרון...נהנתי לקרוא.

מר מתוק
18-10-2010, 14:44:38
שרון,

סקירה שלא הייתה מביישת את אדריכלי RCGROUPS!
כל הכבוד! נהניתי מאד לקרוא ולראות.

תודה,

שחר

sharonx
18-10-2010, 19:32:55
תודה חברים טובים. מקווה שלי ולשאר חברי הפורום הפעילים יהיו עוד הזדמנויות לנסות מוצרים חדשים.
הקישור לסקירה בRCG
: http://www.rcgroups.com/forums/showthread.php?t=1323863

וב RCU
http://www.rcuniverse.com/forum/m_10073816/anchors_10073816/mpage_1/key_/anchor/tm.htm#10073816

umbo
18-10-2010, 20:18:41
סקירה יפה מאוד.

MDreamer
18-10-2010, 21:50:05
כבר יש כמה הזדמנויות בדרך :rolleyes: אחת מהן מאוד מאוד קרובה;)