rotemshan
01-08-2014, 16:07:06
אני מנסה לתכנת בקר של yep .
YEP80
הפעם האנגלית הסינית שברה אותי ולא הצלחתי לפענח את מה שכתוב במדריך שלהם.
אני רוצה לבטל soft start,
עובד על זה כבר שעתיים ללא הצלחה.
למישהו יש כרטיס תכנות?
אלו ההוראות למי שבא לו לפענח
Basic-Setup:
The basic setup goes relatively quick. You should read this Manual thoroughly before running it.
Otherwise one may not be able to keep up with the pace!
1. Verify that the ESC is off, and then switch on the transmitter with the throttle stick at full
power(make sure the full power position with fine trimming).
2. Hold the Model, Connect the ESC with motor and battery pack => a monotonous continuous
beep should be heard. ♪♪♪♪♪♪…: Multiprogramming is activated!
3. Move the stick to the desired neutral position; if the Brake is not needed, the throttle stick is on
the “full back” position. If the Brake is needed, lower the stick to one fifth away from the lowest
point (not fully back), you will hear two beeps (these high pitch and low pitch)to make sure
the position of throttle stick. Then the throttle process was saved.
4. Now, do not move the throttle stick and hear the sounds , it comes the setup of the Soft
start to wait for the acknowledgement of the sounds ,
The Soft Start was saved.
The Soft Start with Brake, if activated, will also use this value!
5. For extremely fast response (NOT FOR HELI USE!!!!), the same operation as (procedure 1-3)
the Basic-setup, after the 3 procedures, please make sure to push the stick back to full power and
wait for acknowledgement . Then come back to full back position swiftly and the ESC is
ready to run and wait for the acknowledgement
=> Quick Start is saved.
=> Quick Start with brake, if activated, will also use this value!
Sent from my SM-N900
YEP80
הפעם האנגלית הסינית שברה אותי ולא הצלחתי לפענח את מה שכתוב במדריך שלהם.
אני רוצה לבטל soft start,
עובד על זה כבר שעתיים ללא הצלחה.
למישהו יש כרטיס תכנות?
אלו ההוראות למי שבא לו לפענח
Basic-Setup:
The basic setup goes relatively quick. You should read this Manual thoroughly before running it.
Otherwise one may not be able to keep up with the pace!
1. Verify that the ESC is off, and then switch on the transmitter with the throttle stick at full
power(make sure the full power position with fine trimming).
2. Hold the Model, Connect the ESC with motor and battery pack => a monotonous continuous
beep should be heard. ♪♪♪♪♪♪…: Multiprogramming is activated!
3. Move the stick to the desired neutral position; if the Brake is not needed, the throttle stick is on
the “full back” position. If the Brake is needed, lower the stick to one fifth away from the lowest
point (not fully back), you will hear two beeps (these high pitch and low pitch)to make sure
the position of throttle stick. Then the throttle process was saved.
4. Now, do not move the throttle stick and hear the sounds , it comes the setup of the Soft
start to wait for the acknowledgement of the sounds ,
The Soft Start was saved.
The Soft Start with Brake, if activated, will also use this value!
5. For extremely fast response (NOT FOR HELI USE!!!!), the same operation as (procedure 1-3)
the Basic-setup, after the 3 procedures, please make sure to push the stick back to full power and
wait for acknowledgement . Then come back to full back position swiftly and the ESC is
ready to run and wait for the acknowledgement
=> Quick Start is saved.
=> Quick Start with brake, if activated, will also use this value!
Sent from my SM-N900